view cart menu separator categories menu separator faq
advanced search
categories  > Miata Stripes (2)
Mazda Miata 8 Inch Racing Rally Stripes plus Pinstripes

Mazda Miata 8 Inch Racing Rally Stripes plus Pinstripes

Price: $44.99 add to cart     
Feedback: 100%, 8 sales Ask seller a question
Shipping: US-Mainland: $9.00 (more destinations)
Sales Tax: Florida: 7%
Condition: Brand new
Payment Options: Money Order, Cashier's Check, Personal Check,
*The store has not been updated recently. You may want to contact the merchant to confirm the availability of the product.
For more of our automobile stripe kits visit .

Dealer Quality 8" wide x 30' long MIATA racing stripe kit with pinstripes.

Designed for the Mazda Miata but will fit virtually any car.

This kit includes a full 30 feet of high quality 8 inch striping cut from "Dealer Quality Vinyl" for only $44.99 with pinstripes. (Pinstripes are applied after the main stripes are installed.) (not shown on car above) You will also receive instructions and a squeegee.



RALLY STRIPE INSTALLATION INSTRUCTIONS - To install our stripe kits first take a pair of scissors and cut the stripes into the lengths you will need for the hood, roof and trunk of your car. Make sure to cut each piece a little longer than the section you are striping. Keep these sections dry and set them aside.

Remove any emblems that may get in the way of the stripe. (replace them after the stripes are applied)

Clean the application area with rubbing alcohol.

After the car is clean, mix in a spray bottle 20 ounces of water, 1/4 teaspoon of unscented clear liquid JOY and 1/2 teaspoon of Isopropyl Alcohol. (if you do cannot get clear liquid joy any dishwashing liquid will work)

I normally find the center of the car and then take a roll of masking tape and run it from the front to the back of the car. If I want the stripes to be an inch apart I use one inch wide tape. If I want them two inches apart I use two inch tape and so on.

Once I have marked where the stripes will go I spray the car with soapy water and then I peel off the backing and spray the adhesive side of the first stripe with the soapy water as well. (remember to peel the backing off before getting the stripe wet) Position the stripe where you want it and slide it into place up against the masking tape you applied. For longer sections is it nice to have a second person help out. As long as the stripe and the car are wet with the soapy water you can work with the stripe. Keep the stripes you are not working with DRY.

Once the stripe is where you want it you simply squeegee it on. Spray a little soapy water on the stripe to allow the squeegee to glide over the stripe without scratching it. (wrapping the squeegee in a soft cloth will also protect the stripe from scratches) Repeat this process on all stripes and then trim any excess vinyl away with an exacto knife or razor blade.

TIP - for bumpers and other curved areas try heating the material with a hair dryer as you apply. This makes the vinyl soft and pliable.
For more instructions visit

If you wish to order with a check or money order you can send $44.99 (with pinstripes) plus $9 shipping along with a description of what you are ordering to

Cole Farms Inc.
1610 Guam Lane
Gulf Breeze, Fl 32563
Other Products from rallystripes:View all products
Mustang 8" Racing Rally Stripes
MUSTANG ROUSH 8" Racing Rally Stripes PLUS Pinstripes
Mazda Miata 8 Inch Racing Rally Stripes
Pontiac Solstice Saturn Sky Racing Stripes 8 Inch
Mustang 10" Precut Racing Stripes Stripe Kit
Last Updated: 18 Jul 2009 14:30:17 PDT home  |  about  |  terms  |  contact
Powered by eCRATER - a free online store builder